Koolance EXT-400SL Uživatelský manuál

Protected by U.S. Patents 6,664,627; 6,313,990; 6,234,240; 5,731,954Other Technology Pending U.S. & World-Wide PatentsSuperior Liquid Cooling Sys

5User ManualLED Display PanelMode 1 operates your system at 45% power until the temperature reaches 51ºC (124ºF), then increases to 100% power.Mode 2

6Chapter2Connecting Exos-LT Systems Connecting Exos-LT Systems

7User ManualThe Exos is designed to operate in various locations, but it must run upright. Air fi ltration is not possible in all orientations.If the E

8External Nozzles & Power CableCut the included 6mm (1/4”) tubing into two segments. You will need to connect each to the Exos’ rear nozzles.Each

9User ManualConnecting the Slot AdapterThe Slot Adapter allows the Exos to connect with any ATX computer through an available card slot. It is respons

10Install the Slot Adapter into any available rear card slot in your computer.Screw the Slot Adapter in place as you would a normal device.From the re

11User ManualPower ConnectionThe Exos-LT requires approximately 8-10W from any standard ATX power supply. Since it is adapted internally, it does not

12ATX Power SwitchThe ATX “pass through” lead is responsible for shutting off your computer if the temperature sensor reaches 58ºC (136ºF) (See LED D

13User ManualThe components in the Exos-LT should be connected in series. Each system contains a heat exchanger and reservoir, but you must choose whi

14Nozzles are designed to attach tightly. If you need to remove a hose for any reason, it may not pull off easily, even after unscrewing the compressi

iUser ManualThis User Manual is updated regularly. Please be sure to check our support page for a newer version of this guide: www.koolance.com/suppor

15User ManualHose LengthsBefore installing your liquid coolers, appropriate lengths of tubing must be cut to connect each device. It is generally easi

16Continue connecting all of your coolers in the system until there are no longer any open tube ends.Liquid CoolersYou should now install the liquid c

17User ManualChapter3Filling & Maintenance

18Once all of the coolers have been con-nected, the system can be fi lled with coolant. The refi ll plug is located on top of the reservoir. Remove the

19User ManualAllow the pumps to run for about 1-5 minutes. When fi ltration has ended, the liquid noise should stop. If the reservoir level becomes sig

20The coolant in your system should be emptied for any of the below reasons. Unless replacing the liquid coolant, it can also be reused.1. To Keep it

21User ManualYour Koolance system is designed to provide years of reliable cooling. To help avoid unnecessary product returns, we have prepared this l

224. After the system has been on for awhile, the temperature alarm sounds...Make sure that the LED temperature reads at least 55ºC (131ºF) or higher

23User Manual6. My system appears to be leaking fl uid...Since users are allowed to confi gure their own coolers and clamps, it is possible a connection

24Limited WarrantyDisclaimerKoolance Incorporated (“Koolance”) warrants each new Koolance liquid-cooled system (“the system”), against defects in mate

iiWARNING: The Koolance liquid & coolant pack contain chemicals which may be harmful or fatal if swallowed. KEEP THIS AND ALL DANGEROUS CHEMICAL

www.koolance.comISO 9001Printed in Korea

iiiUser ManualTable of ContentsIntroduction 1Exos-LT System Diagram ... 4L

iv Exos-LT Series Systems: - External Power Cable - Slot Adapter - Rubber foot pads - ATX power jumper wire - refi ll funnel - liquid coolant mixtu

1User ManualChapter1Introduction

2 Congratulations on your purchase of a Koolance system!As the most sophisticated product of its kind, Koolance offers many unique features found now

3User ManualThe heart of a liquid cooling system is the pump. This device pushes liquid through each cooler and into the heat exchanger. Koolance syst

4 IntroductionExos-LT System DiagramReservoir & PumpsRadiator Cooling FansReservoir Refi ll PlugCoolant InletPower ConnectionLED Display PanelRe